1. Reset Yun to factory default by:

reset-to-factory-anyway
reboot

2. Setup static ip at wan:

nano /mnt/sda1/setwanstaticip.sh
#!/bin/ash
uci set network.wan.proto=static
uci set network.wan.ipaddr=192.168.241.1
uci set network.wan.netmask=255.255.255.0
uci commit network
/etc/init.d/network restart
chmod 755 /mnt/sda1/setwanstaticip.sh
/mnt/sda1/setwanstaticip.sh

 

 

 

 

 

Write comment (0 Comments)

 

Autodetect AVR PART show unknow. Upload will be failed. 

avrdude: AVR device not responding 
avrdude: initialization failed, rc=-1 
Double check connections and try again, or use -F to override 
this check. 

To confirm the problem by:

1/ Enable the NTB0104 level shift by set high to GPIO19: commands is as below:

echo 1 > /sys/class/gpio/gpio19/value

2/ Check if MOSI/MISO/SCK/RST hardware connection works as expect, below is the PIN mapping with the GPIOs. User can export the GPIOs in linux and run the commands as below to set high / low to GPIO. The related SPI pins will be high(+5V) / low accordingly and can be check by a multimeter.  Low is 0v and high is 3.3v or 5v depends on the Arduino board.

Below is the commands need to type and check whether GPIO works.

echo 1 > /sys/class/gpio/gpio19/value   // enable level shift

echo 18 > /sys/class/gpio/export     //export gpio 18
echo "high" > /sys/class/gpio/gpio18/direction   // set direction to out and set level to high
echo "1" > /sys/class/gpio/gpio18/value   // set this GPIO to high, SPI_SCK should be high in the ICSP header.
echo "0" > /sys/class/gpio/gpio18/value   // set this GPIO to low, SPI_SCK should be low in the ICSP header.

echo 21 > /sys/class/gpio/export     //export gpio 21
echo "high" > /sys/class/gpio/gpio21/direction   // set direction to out and set level to high
echo "1" > /sys/class/gpio/gpio21/value   // set this GPIO to high, SPI_MOSI should be high in the ICSP header.
echo "0" > /sys/class/gpio/gpio21/value   // set this GPIO to low, SPI_MOSI should be low in the ICSP header.
 
echo 22 > /sys/class/gpio/export     //export gpio 22
echo "high" > /sys/class/gpio/gpio22/direction   // set direction to out and set level to high
echo "1" > /sys/class/gpio/gpio22/value   // set this GPIO to high, SPI_MISO should be high in the ICSP header.
echo "0" > /sys/class/gpio/gpio22/value   // set this GPIO to low, SPI_MISO should be low in the ICSP header.

echo 20 > /sys/class/gpio/export     //export gpio 20
echo "high" > /sys/class/gpio/gpio20/direction   // set direction to out and set level to high
echo "1" > /sys/class/gpio/gpio20/value   // set this GPIO to high, SPI_RST should be low in the ICSP header.
echo "0" > /sys/class/gpio/gpio20/value   // set this GPIO to low, SPI_RST should be high in the ICSP header.

 

 

 

 

 

 

Write comment (0 Comments)

Get hex file from arduino sketch

Make sure the Yún shield and your computer are on the same network, and open a browser.  Connect to the Yún shield's web panel page by entering the IP address. Once logged in (default password:dragino), 

User can check them in the Web GUI--> Sensor page. The Dragino Yun use avrdude to program AVR

Password: dragino (default) 

The Dragino Yun GUI supports different kind of Arduino/AVR boards includes:

  • Arduino Leonardo or Mega32u4
  • Arduino Uno or Mega328p
  • Arduino Mega2560 or Mega2560

Write comment (0 Comments)

With return character:

#include <Process.h>
void setup() {
 Bridge.begin();  // Initialize Bridge
}
void loop() {
 int temperature = random(0, 100);
 Process p;              
 p.begin("/mnt/sda1/db.php");      
 p.addParameter(String(temperature)); 
 while (p.running());
 while (p.available()) {
    char c = p.read();
    Serial.print(c);
 }
 delay(1000); 
}

With return integer:

#include <Process.h>
void setup() {
 Bridge.begin();  // Initialize Bridge
}
void loop() {
 int temperature = random(0, 100);
 Process p;              
 p.begin("/mnt/sda1/db.php");      
 p.addParameter(String(temperature)); 
 while (p.running());
 while (p.available()) {
    int result = p.parseInt();          // look for an integer
    Serial.println(result);       // print the number as well
 }
 delay(1000); 
}

 

Write comment (1 Comment)